Showing results: 256 - 270 of 333 items found.
-
PFK-105 -
Prostat Corporation
- Ionization Test Kit for Measuring Offset Voltage and Discharge Times- Includes a Field Meter, Charge Plate Monitor, ±1000 Volt Charger and Decay Timer- Balance Ionizers per ANSI/ESD SP3.3 Periodic Verification- Measure Ionizer Decay time as per ANSI/ESD S3.1 and ANSI/ESD SP3.3.- Measure Body Voltage Generation and Decay- Evaluate Ionizers and Packaging Materials- Includes a fixture to hold the PFM-711B, CPM-720B and PDT-740B as one- Molded Carrying Case with Foam Insert Included
-
H337H-2 -
Howell Instruments, Inc.
• Verifies engine performance duringtroubleshooting and after modulereplacement • Permits on-wing Interturbine Temperature(ITT) trim adjustment • Verifies aircraft ITT, torque and speedaccuracies in the specific engine applications • Requires minimal time for set-up and testing • Measures and displays various engineparameters and calculates functions duringflight line and test cell engine runs including: - ITT Setting (Trim Resistor) - ITT and Gas Generator Speed Margins - Compressor Efficiency - Cockpit Gage Verification (ITT, Torque, GasGenerator Speed and Propeller Speed)
-
140BMC/6P -
Aines Manufacturing Corp.
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
TP800110 -
Total Phase Inc.
The Total Phase Advanced Cable Tester v2 is the quickest and most convenient way to comprehensively test USB, Lightning, and video cables. It provides:*Short testing - Dynamic visualization of test results*Open testing - Dynamic visualization of test results*Continuity testing - Dynamic visualization of test results*DC resistance measurement for most wires, with milliohm precision on ground and power wires, ohm resolution on most other wires, continuity check only on high-speed data lines*Signal integrity testing of data lines to 12.8 Gbps per channel*E-Marker verification*Lightning plug bring up/function (Apple Lightning Cables)**Over-voltage protection (Apple Lightning Cables)**Voltage recovery testing (Apple Lightning Cables)**Quiescent current consumption (Apple Lightning Cables)*
-
VerOLink -
Verocel, Inc.
VerOLink (Verify Object Linking) is a verification tool (DO-178B, DO-330, IEC 61508 and ISO 26262) that helps satisfy the control coupling objective. Control coupling provides a measure of the correctness of the integration of many independently compiled object files linked to form a single executable image. Even if all requirements based tests are performed on the integrated executable image and the coverage is measured at the object code level without instrumenting the code, the possibility still exists that the linker could have linked a function call incorrectly. VerOLink is used to provide this final check. Verification of the code integration is fully automatic with VerOLink. The tool analyzes the executable image to find all functions and all function calls and their locations in the object files. By analyzing the object files used in an application, VerOLink verifies that the function calls within an executable image have been resolved correctly when the linker combined the object files
-
Tekscan, Inc.
Tekscan is the leading manufacturer of tactile pressure sensors and measurement systems. Our pressure mapping systems are used by product designers and test engineers throughout the research, design, testing, and manufacturing cycle to verify and enhance product performance. The informative data allows companies to save money in design, design verification, reengineering, and machine set-up costs.
-
ACCAT -
Huntron
The ACCAT is designed to support diagnostic and acceptance test requirements across a wide spectrum of testing parameters. ACCAT provides a suite of core parametric test instruments, advanced GUI based software, Huntron Access Robotic probing and Huntron Analog Signature Analysis (ASA). ACCAT provides stimulus and asurement capabilities necessary for full functional and parametric testing of circuit card assemblies along with robotic guided probes for fault verification and debug. The Huntron ASA test is ideal for pretest or safe to power up procedures protecting the integrity of the test system.
-
Acculogic, Inc.
Acculogic offers a powerful suite of PC-based hardware and software tools specially designed for testing of electronic devices, boards and systems using the IEEE1149.1 and IEEE1149.6 standards. Acculogic’s comprehensive line of Boundary Scan Test tools can be effectively used in the entire product life cycle, starting with design verification and validation and continuing into pilot production and manufacturing. Use of these tools in field service and repair depots can help further to reduce test cost and cycle time.
-
50-295A-021-5/16 -
Pickering Interfaces Ltd.
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
50-295A-121-6/24 -
Pickering Interfaces Ltd.
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
50-295A-121-18/8 -
Pickering Interfaces Ltd.
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
50-295A-021-3/24 -
Pickering Interfaces Ltd.
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
50-295A-021-10/8 -
Pickering Interfaces Ltd.
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
50-295A-021-5/12 -
Pickering Interfaces Ltd.
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
50-295A-121-10/16 -
Pickering Interfaces Ltd.
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
